February 26, 2020

Wide variety of servo gearboxes, designed to fit almost all servo motors on the market
Designed for the highest torsional stiffness and the cheapest angular backlash, intended for the maximum torque and overhung loads
Bush with slot machine games and hub clamp for servomotor coupling
Enhanced dimensional compactness due to direct servomotor coupling
Widest range of feasible servomotors coupling dimensions.
The correct technical solution because of a comprehensive selection of sizes, gear stages, transmission ratios, designs and non-standard designs.
Servo equipment reducers (worm, coaxial, helical and bevel helical units) Catalog SR
Operating instructions:
Operating instructions for equipment reducers and gearmotors (UTD.045)
EP Drive Systems, Inc. is very happy to announce the expansion of our range of Servo Reducers, today offering five levels of precision to meet up any application requirements. The five degrees of precision obtainable allows a machine designer to select the required reducer precision to meet up their needs and their budget. They are available in both in-line and right-angle variations, in torques up to 7,376 lb.ft. and ratios to 3,392:1.
Usual applications for these reducers include rotary & linear axis drives, and materials handling axis drives. Industries offered include Material Managing, Automation, Aerospace, Machine Tool and Robotics.
The mounting faces of the HT, HP, Electronic and B versions are identical, which makes it possible to interchange a unit with a higher or lower accuracy unit if needed.
A wide range of engine couplings and installation flanges are for sale to the entire reducer range to install virtually any servo electric motor and the hollow bore output can be used to attach output shafts, pinion shafts, or other drive elements.
These reducers are typically selected predicated on the peak cycle forces, which often happen during accelerations and decelerations. These cycle forces rely on the powered load, the speed vs. time profile for the routine, and any other exterior forces acting on the axis. For more selection info, please follow this PDF hyperlink.
For application & selection assistance, please call, fax or email us. Your application info will be examined by our engineers, who will recommend the very best solution for your application.
EP Inc. provides a full range of modular servo gearboxes /worm reducers. The modular style permits configurations with motor insight flange and output pinion for rack and pinion drives, in addition to solid output shafts, Hollow bore result, and input shafts for all other positioning applications. The modular design allows for universal mounting of the gearbox in virtually any orientation.
They can be used on motors with a NEMA23 standard flange through an adaptor kit. As the gears are naturally angled, they lead to a short total amount of the motor and its gear.
The series can also be delivered both right- and left-angled and with output shafts on both sides. A 30-mm machine recess for centering and a 4 M5 threaded mounting hole may also be built on the gear’s output side.
Built with a simple and robust style, the series offers gearing ratios that range from 6:1 to 75:1. An individual may also customize the components through the order, so as to match the apparatus to its intended app.
The Precision Planetary Gears of the EPRG series contains a thorough range of low backlash planetary gearboxes, with up to class 3′ precision, obtainable in several gear frame sizes, with single or multiple stage reduction (for gear ratios from 1:3 to at least one 1:1,000). These models also include versions with dual shaft, right position shaft and right position output, as well as a full selection of adapters for engine mounting, making them capable of meeting the requirements of also the most diverse applications. They are designed for make use of with integrated servo and stepper EP motors, mounted directly or via adaptor flanges, but can also be used with other EP electric motor types. This selection of products is based on years of experience and represents the outcome of a decade-long research targeted at improving performance.
Maximum precision and dynamics, coupled with exceptional torque density, are the key requirements specified for reliable servo gearboxes used. EP provides servo gearboxes for any application and any efficiency range. Our low-backlash planetary and right-angle gearboxes reflect our enthusiasm for advancement and the best levels of precision.
Worm equipment reducers provide market advance solution with efficiency and flexibility. Low quantity of basic models could be applied to a wide selection of power ratings guaranteeing top performance and decrease ratios from 5 to 1000.
Gear reducers and servo gearboxes of EP Precision Machinery Co., Ltd. are created for high-performance mechanical devices. When the motor velocity needs to be reduced, the result torque improves and send torque totally to the application. We believe that customers will appreciate our gear reducer to achieve their demand. Just check out EP, you can get more information regarding servo gearheads, servo gearboxes, and gear reducers. We continue to keep going forward for your support.
Plug the Quickness Reducer into the desired channel of your receiver, and plug the lead from your servo (or servo wye) in to the male servo lead from the circuit table. The arranged screw on the blue trim pot, located near the top of the primary circuit board, is utilized to control the velocity of the servo. Change the set screw completely clockwise (CW) for normal servo speed with no speed reduction, fully counter-clockwise (CCW) for optimum speed reduction, or anywhere in between for partial swiftness reduction. The red LED indicates three possible conditions: Gradual Blinking = No Signal; Solid On = No Quickness Reduction; Fast Blinking = Reduced Acceleration Setting
Please note that if you make any change to the speed setting as the receiver is on, you must cycle capacity to the receiver (change if off and back again on) for the brand new speed establishing to take effect. This circuit can also be used in conjunction with this Servo Reverser to trigger flap or retract servos to turn in opposite directions for correct function. Guidelines are included for easy set up and use.
IMPORTANT NOTE: This device will only focus on a regular, proportional servo. You won’t focus on a retract-type servo, as they do not understand any servo positions apart from clockwise (CW) and counter-clockwise (CCW). Retract servos can’t be slowed down, actually by a transmitter that includes this function, as their design and electronics do not allow it. Verify the FAQ page for more information.
This device will reduce the speed of any regular, proportional servo. Connect it in the middle of your receiver and the servo (or servos) you intend to control for a far more scale-like movement of flaps or retracts. Adjustable, it could be set to reduce the speed of your servo from super-slow movement to no speed reduction at all, with an almost infinite amount of positions in between. Maximum reduction period for a servo to visit 90 degrees is approximately 14 seconds, minimum time (no reduction) is merely the normal rate of the servo. Great for reducing or removing the tendency of a plane to “balloon up” when flaps are deployed. It can be used to control several servo by use of a normal servo Y.
This is the new regulated version that can be used on radio systems powered by any size or kind of battery, including 4.8-6.0 volt 4-5 cell Ni-Cad/Ni-MH batteries, and HV (high voltage) receivers that are powered by 2-cell 6.6-8.4 volt Li-Po/Li-Ion/Existence batteries. This unit won’t reduce the voltage likely to your servos.
The EP Gear Reducer is the perfect solution for servomotor applications such as for example packaging machines, gantries, injection molding devices, pick and place, and linear slides.Provided in concentric shaft, right angle solid shaft, and correct angle hollow shaft designs with modular adaptor flanges and keyless compressible bushings to quickly mount to any manufacturer’s servo engine. The EP Series helical gears possess slanted teeth compared to spur gears with straight cut teeth, creating a smoother gear mesh, yielding significantly lower noise levels.
The low backlash EP planetary servo gear units are designed for the 30 to 350 Nm (265 to 3100 lb-in) torque classes. These were designed to combine the best possible versatility and cost-efficiency because don’t assume all application requires high-performance elements.
They provide a basis for diverse, dynamic and cost-optimized drive solutions.
The EP planetary servo equipment units can be found in the following versions:
PSC = B5 output, easy output shaft
PSKC = B5 result, with keyway
PSCZ = B14, result, smooth output shaft
PSKCZ = B14 result, with keyway

If you have any kind of questions concerning servo gear reducer, maintain reviewing our experts’ articles.